Free Member
Language :
BATAVIAGROUP
BATAVIAGROUP
http://indotrade.co/bataviagroup/
BATAVIAGROUP
Contact Information
Name:

Mr. IZAR HALKY [Marketing]

E-mail:
Homepage:

Instant Messaging:

Y!: bataviaonline@yahoo.com 
Phone Number:

Phone number of Mr. IZAR HALKY at Tangerang

Mobile Number:

Mobile number of Mr. IZAR HALKY at Tangerang

Fax Number:

Fax number of Mr. IZAR HALKY at Tangerang

Address:

jl.muhasyim rt01/01 larangan cileduk
Tangerang 15154, Banten
Indonesia

Average User Review

There is no review for this company

Write a review

Sell

Bataviagroup Jual Spiegel Relaskop : Alat Ukur Dimensi Pohon Hub 0856 93299100[Oct. 19, 2011 22:00:56]
PriceNego
Quantity Order:
Payment MethodTelegraphic Transfer (T/T), Cashier Order
QuantityReady Stock
Pack. & DeliveryBox
Spiegel Relaskop : Alat ukur dimensi pohon
An sophisticated, compact and robust but expensive instrument for measuring height, diameter, basal area and range.

This hand-sized tree measuring instrument features multiple capabilities: Rangefinder measures 33' , 66' , 99' or 132' baselines.

Clinometer measures plus or minus vertical angles with readings in degrees or percentage.

Dendrometer measures tree diameter outside the bark, at any height.

Angle Gauge provides direct measures of basal area per acre.

FEATURE

Slope Correction Device gives topographic correction when using two chain tape with trailer.

Used by foresters since 1954, the Relaskop combines six instruments into one. Saves time and money when cruising timber, variable plotting or Three P sampling. Each unit weighs only 14 oz.; furnished complete with leather case and instructions.

American Scale reads In English units ( sq. ft./ acre, inches, feet) for BAF 5, 10, 20 and 40. Also includes a 66' slope correction scale. Ideal for use on trees smaller than 96" dbh.

SPECIFICATION

General instruction for use of the Relaskop for measuring diameter:

1. Measure the desired horizontal distance ( H metres) from the base of the tree ( or point directly beneath the desired tree site) to a location where the required point ( eg change in diameter) can be seen. Note that you must be at least 5 m away for every 20 cm anticipated diameter.

2. Sight at the required point, while holding the break button to allow the scales to freely rotate.

3. Read from the diameter scale once the scale has settled the number of large bands ( with the number 1 printed on them) ( L) ; the number of small bands ( 4 narrow bands immediately to the right of the large 1 band) ( S) ; and an estimate of any fractional small band ( s) . Estimate the fractions of the small band as 0.2 ( just into the band) , 0.4 ( almost half) , 0.6 ( just over half) , 0.8 ( amost full narrow band) .

4. Diameter is calculated as d ( cm) = H* ( L+ 0.25* ( S+ s) ) * 2

5. Check to ensure the diameter appears correct. Note that L will be 0 or 1, S will be 0, 1, 2, 3, 4 and s will be a fraction less than 1.0.

http: / / www.bataviagroup.indonetwork.co.id

mail: izar_bos03@ yahoo.co.id

mail : bataviaonline@ yahoo.com

Hub : IZAR Halky

Tlp : 021-91143015

tlp : 021-37345044

Hp : 0856 932 99100

Fax : 021-7318569
You have [3] new inquiries. Go to Member Menu
Home - Trade List - Product List - Inquiry List - Cooperation List - Company List
Copyright © 2024 Indotrade.co. All Rights Reserved.