Specification

Achievement Test Equipment Gas Fueled Engines and Diesel.
Main Function:

* Measure the maximum peak cylinder pressure
* Measure the lowest peak pressure cylinder
* Measure the average peak cylinder pressure
* Measure the standard deviation of the peak cylinder pressure
* Measure the maximum gradient / slope of the curve of cylinder pressure

Is a test tool for monitoring the condition of the engine at speeds up to 4000 rpm. Equipped with the data evaluation software and store data to show changes in peak pressure ( peak pressure) in the form of graphic display.

* Evaluation of data in the field immediately
* 2 x 20 memory locations
* Easy to Use
Description

Achievement test equipment is operated with beterai machine to measure the cylinder pressure is between 1 and 100 cycles, and then from there arithmetical calculations obtained an average value of peak pressure, standard deviation, gradient / slope of the curve maximum cylinder pressure and cylinder pressure curves average . Numerical data will be visible on the LCD screen and can be stored as necessary. The average curve of pressure / pressure that has been printed can be re-analyzed using the data evaluation software that is included in accessories. Since the pipe length indicator causes the oscillation of gas that would obscure the signal measurements, the cylinder pressure signal can be mashed with l ow-pass filter that can be set ( adjustable) . Measurement data can be stored in two memory locations, each with a 20 record that is " as found" / " as left" . With the ability of the above, then the tester of this new technology is ideal for balancing ( balancing) cylinder of gas-fueled engines and diesel. There are additional functions that the peak pressure can be displayed without any time limitation. Analog sensor signals can also be transmitted through the output that is available on the monitor for continuous monitoring purposes, it is recommended to use the power-adapter

Art.No: 5510293
Application:
* To measure the indicator valve
* For continuous monitoring
* Balancing ( balancing) cylinder of gas-fueled engines and / or diesel fuel.

Technical Data
Measure Range
Type 2516A1
bar 0 ... 250
Type 2516A2
Bar 0 & 250
Input Voltage Range
Type 2516A1
V 1 & 15
Type 2516A2
V 1 & 7
Sensor sensitivity ( adjusted)
mV / bar 7 & 40
Pressure value display accuracy ± 0.5% d Resolution Engine Speed Range 0.1 bar min -125 & 4000 ° C operating temperature 0 & 50 Total Cycles pressure?
1 & 100 Low-pass filter ( 5th order Butterworth) 300 Hz, 500, 1500, 5000
Total Memory Capacity per-second data memory 20 data Record Sampling Rate per round? 720 Views 128x64 dot graphic LCD monitor output? Neg.Output BNC ( monitor) 5 V RS-232 Interface? D-Sub 9 pol. Neg.Dimensi Type 2516A1 / A2mm Type 2516A10 62x92x45 Dimensions 452x327x100 mm Weight 350 g Battery Type 39V / EC6LR61 disposable hours Age> 10 Combined with Record Type 6613CA measurement data consist of numbers, the flow curve, number, date and time memory allocation Functions Measurement of the maximum peak pressure p max p min cylinder lowest peak cylinder pressure p av average peak pressure cylinder S dev Standard deviation of the peak cylinder pressure dp / ca maximum value of the gradient / slope of the curve of cylinder pressure the r / min speed value of p peak cylinder pressure peak value latest; measurement function is not restricted by time av p Value Function Benefit average peak pressure in the engine cylinder. This value is calculated from the average peak pressure ( p av) stored on a memory block. The value of this calculation is displayed and always gets updated every new data

Pressure curve

Pressure curve with an average resolution of 720 dots per one rotation, which could print out via RS-232C Interface.

Figure 1 Curve of pressure from the six-cylinder gas engine, before and after construction maintenance ( " as found" / " as left" )

Software

Pressure curve can be displayed graphically using a Windows-based software is included in the accessories.

Pressure curves of the entire cylinder can be unified? as a feature to verify the engine cylinder balancing.

Function Benefits

Setting all parameters measured through the LCD keyboard

Monitoring Functions

There is a battery symbol on the display; Achievement Measure Tool Fueled Engines Gas and Diesel will be off automatically after two minutes of the last keypress, except when this function is not activated

Figure 2 Table data with numerical values, before and after construction maintenance ( " as found" / " as left" )

Figure 3 Deviation of the peak pressure p av of each cylinder of the engine peak pressure compared with the average calculated, before and after construction maintenance ( " as found" / " as left" )

Figure 4 Diagram Trunk

Composition Package

" Cylinder pressure sensors with amplifiers piezotron

" Adapters for connection to the indicator valve)

" Tubular socket wrench

" Special spanner wrench

" Software for data evaluation

" Power adapter

" Case

Optional Accessories:

" USB / RS-232C converter.

Alatuji.

Contact Person: Fikri ( 0815 614 1954, 0811 893 101) .

Address: Jl. Revolutionary Hero No. 22B.

Tel. + 62-21-8611 131, 259 8611.

Fax: + 62-21-8611 207

EMAIL: sales@ alatuji.com

Website: www.alatuji.com